Search found 78 matches
- Tue Oct 04, 2016 10:42 pm
- Forum: QuickStart
- Topic: annunciator comm ch2 trouble
- Replies: 6
- Views: 6925
Re: annunciator comm ch2 trouble
you probably set it for class A network
- Sat Sep 17, 2016 9:55 pm
- Forum: EST3
- Topic: Diagnostic faults on SIGA MAB's
- Replies: 8
- Views: 5331
Re: Diagnostic faults on SIGA MAB's
route them to nowhere if you aren't using FT or common trouble contacts for central station
- Tue Jul 05, 2016 10:01 pm
- Forum: EST3
- Topic: Diagnostic faults on SIGA MAB's
- Replies: 8
- Views: 5331
Re: Diagnostic faults on SIGA MAB's
microcode?
- Thu Feb 04, 2016 8:14 pm
- Forum: IRC3
- Topic: Upgrade IRC3 to IO500 notes
- Replies: 1
- Views: 6000
Re: Upgrade IRC3 to IO500 notes
I just upgraded a IRC3 to a IO500. The main problem was the inability to get the zone descriptions and the 4D map if the SLC loop is lifted only the first 15 point descriptions are display after that it is only numbers. Also I was unable to get the point number (zone) and the serial number together...
- Thu Dec 24, 2015 12:13 pm
- Forum: QuickStart
- Topic: program a cr to activate during reset phase
- Replies: 0
- Views: 2294
program a cr to activate during reset phase
Anyone here have a clue how to use the reset pseudopoint to toggle a relay? It's in the help file (monitor point) but doesn't give an example. It's also not available in the correlation screen. Thanks nevermind, there's a tab you click to setup the input event for the output response. It actually wo...
- Sun Dec 13, 2015 6:23 pm
- Forum: EST3
- Topic: guide for EST3 network communication
- Replies: 5
- Views: 5725
Re: guide for EST3 network communication
how did you wire panel 6 to the network? It sounds like you removed the wiring for panel 2 when you connected panel 06. the network wires are probably mislabeled or the splice is incorrect. As AB posted, check your wiring.
- Sun Dec 13, 2015 6:14 pm
- Forum: EST3
- Topic: how can change cabinet address?
- Replies: 4
- Views: 2880
Re: how can change cabinet address?
AB, tech support said the 1 doesn't matter
- Sat Sep 19, 2015 11:25 pm
- Forum: EST2
- Topic: need help on 2 panel. map error, autocnfig, internal mem
- Replies: 3
- Views: 3225
Re: need help on 2 panel. map error, autocnfig, internal me
Most likely you have a bad 2-MCM (or 2-lcx). Sometimes a bad device will cause an internal error. If you remove the data loop wire and download a test program with nothing in it and still see the error, you know for sure.
- Thu Aug 20, 2015 9:28 pm
- Forum: Other FACP
- Topic: FACP dialing the CS with PULSE not working
- Replies: 1
- Views: 3431
Re: FACP dialing the CS with PULSE not working
I was just at a customer that install a comcast router with 2 phone lines to replace the copper lines. the set was trying to dial out using pulse dialing and it would not work. want in and out of programming (V32FB) to reset the comm fail on the set so it would dial out DTMF. it looks like at least...
- Thu Aug 20, 2015 9:08 pm
- Forum: EST3
- Topic: Proper FA wire for EST- 3 devices
- Replies: 15
- Views: 8301
Re: Proper FA wire for EST- 3 devices
siga-sd's are the problem. Keep swapping the bad ones out, after 6 months or so you wont have any more problems. same with mapping fault and siga2-ps detectors.